国产熟妇毛多 久久久久一区,91ThePorn国产,91人妻人人澡人人爽人人爽,欧一美一性一交一乱一乱一视频

產品中心
PRODUCT CENTER

  • 聯系人 : 曹鏡森先生
  • 聯系電話 : 0769-82226193
  • 傳真 : 0769-82226193
  • 移動電話 : 15989458768
  • 地址 : ** 廣東省東莞市大朗鎮仙村仙一區99號
  • Email : caojingshen@126.com
  • 郵編 : 523792
  • 公司網址 : http://www.accfirst.com
  • MSN : caoshingcer@126.com
  • QQ : 454992321
  • 聯系人 : 曹鏡森
  • 聯系電話 : 0769-82226193
  • 傳真 : 0769-82226193
  • 公司網址 : http://www.accfirst.com/
文章詳情

Plastic crusher maintenance

日期:2025-04-03 01:33
瀏覽次數:486
摘要:Plastic crusher maintenance 1, should be machine side plastic crusher placement ventilation position, to ensure that the motor heat dissipation, to extend its life. 2, should be regularly filling the bearing lubricating oil to ensure the lubrication between the bearings. 3, regularly check the tool screw, the new plastic crusher after 1 hour, with a tool to tighten the knife, set the screw, to strengthen the blade and the fixed between the knife. 4, in order to ensure the sharpness of t
Plastic crusher maintenance

    1, should be machine side plastic crusher placement ventilation position, to ensure that the motor heat dissipation, to extend its life. 2, should be regularly filling the bearing lubricating oil to ensure the lubrication between the bearings. 3, regularly check the tool screw, the new plastic crusher after 1 hour, with a tool to tighten the knife, set the screw, to strengthen the blade and the fixed between the knife. 4, in order to ensure the sharpness of the cutter incision, should always check the tool to ensure its sharpness, reduce the blade blunt caused by other parts of the unnecessary damage. 5, the replacement of the tool, the knife and the knife between the gap: 5HP crusher 0.8MM better, 3HP below the crusher 0.5MM is better. The thinner the recovered material, the gap can be properly adjusted. 6, before the second start, you should first clear the remaining pieces of the machine room to reduce the starting resistance. Should always open the inertia hood and pulley cover, remove the flange below the gray mouth, because the plastic crusher room discharge powder into the shaft bearings. 7, the machine should be kept well grounded. 8, regular inspection of plastic crusher belt is loose, timely tightening.
   
Plastic crusher maintenance  Machine edge plastic crusher Note:
        1, do not casually replace the pulley, to prevent the speed is too high to cause the explosion chamber explosion, or too low speed affect the efficiency of the pulverizer.
       2, the work should always pay attention to the operation of plastic crusher, first of all, to send evenly to prevent blocking the waste room; Second, do not work for a long time overload. If you find a vibration, noise, bearing and body temperature is too high, such as spraying out of the phenomenon, should immediately stop checking, troubleshooting can continue to work.
       3, machine edge plastic crusher before starting, first turn the rotor by hand, check the claws, hammer and rotor operation is flexible and reliable, broken room with or without collision phenomenon, the direction of rotation of the rotor and the direction of the arrow pointed to the same, Power machine and machine edge plastic crusher lubrication is good.
            4, machine edge plastic crusher should be maintained after the first idle 2 ~ 3min, no abnormal phenomenon after feeding work.
             5, machine edge plastic crusher and power unit to be installed firmly. If you need plastic crusher long-term fixed operation, it should be fixed on the basis of cement; if the need for plastic crusher flow operation, the unit should be installed in the corner made of iron on the base, and to ensure that machine edge plastic crusher belt wheel In the same plane of rotation. 6, machine edge plastic crusher after installation to check the fastening parts of the fastening, if loose to be given to tighten. Also check the belt tightness is appropriate.

Plastic crusher maintenance  Machine side plastic crusher maintenance precautions
    1, before starting, should first use the manpower to move the wheel two or two laps, to confirm the movement after the flexible, you can start. Such as crusher after the normal operation of the material. Off the motor power supply. Whether the machine is damaged.
 2, stop running, you should stop the feed and the material in the machine net, and then cut
    3, in operation, pay attention to the bearing temperature, so that the bearing to maintain a good lubrication, and
    Note whether the sound and vibration are abnormal. When the abnormal situation is found, it should be checked whether the object is not broken easily stuck.
4, to keep the crusher feeding uniform, to prevent overload. Prevent metal and wood and other items can not be broken into the machine. Can not be broken, the feed water can not be too high; wet crushing, you need to maintain the appropriate amount of water to prevent the lack of water and blocked, reduce production capacity. And take appropriate measures to eliminate 5, check the crushing product size is to meet the requirements. If more than the provisions of the size of the particles too much, you should find out the reasons (such as the screen bar gap is too large, the nest is too wide, hammer wear, etc.), 6, crusher parking, to check whether the fastening bolts, 7, grinding wear degree how. For the buttocks, you should also use the opportunity to get rid of the wood caught between the teeth. Damaged parts should be replaced or repaired in time. Save trouble, leaving the insurance device failure. Dayun series of plastic crusher to use Note:
    8, machine edge plastic crusher maintenance of the insurance device, to maintain a good condition.
1, machine edge plastic crusher maintenance and power units to be installed firmly. If you need plastic crusher long-term fixed operation, it should be fixed on the basis of cement; if the need for plastic crusher flow operation, the unit should be installed in the corner made of iron on the base, and machine edge plastic crusher pulley groove The same rotation plane. is it suitable.
 2, machine edge plastic crusher after the installation of the fasteners to check the tightening of the situation, if loose to be given to tighten. At the same time to check the belt tightness 3, machine edge plastic crusher before starting, first hand rotating the rotor, check the claws, hammer and rotor operation is flexible and reliable, broken room collision phenomenon, the rotor rotation direction and machine Arrows in the same direction, power and plastic crusher lubrication is good. 4, do not casually replace the pulley, to prevent the speed is too high to 5, plastic crusher should be kept after the start of the explosion chamber explosion, or the speed is too low impact on the efficiency of the mill. Its first idle 2 ~ 3min, no abnormal phenomenon after feeding work.
    6, machine edge plastic crusher maintenance work should always pay attention to the plastic crusher

    Operation, first of all, feeding to be uniform, to prevent blocking the waste room; Second, do not work for a long time overload. If you find a vibration, noise, bearing and body temperature is too high, such as spraying out of the phenomenon, should immediately stop checking, troubleshooting can continue to work.


Plastic crusher maintenance

Note 1, before starting, should first use the manpower to move the drive wheel one or two laps, to confirm the movement is flexible, you can start. Such as crusher after the normal operation of the material.

 2, crusher parking, to check the fastening bolts are solid, easy to wear parts of the degree of wear and tear. For the buttocks, you should also use the opportunity to get rid of the wood caught between the teeth.

3, in operation, pay attention to the temperature of the bearing, consult the bearing to maintain a good lubrication, and pay attention to the sound and vibration with or without exception. When abnormal conditions are found, it should be checked whether the objects are not broken or jammed.

 4, wear parts, should be replaced or repaired in time.
  5, check the crushing product size is to meet the requirements. If too much of the specified size of the particles, should find out the reasons (such as the screen bar gap is too large, the nest is too wide, hammer wear, etc.), and take appropriate measures to eliminate. 6, stop running, you should first stop the feed and the material in the machine net, and then cut off the motor power. 7, to keep the crusher feeding uniform, to prevent overload. Prevent metal and wood and other items can not be broken into the machine. Can not be broken, the feed water can not be too high; wet crushing, you need to maintain the appropriate amount of water to prevent the lack of water and blocked, reduce production capacity.
 8, the crusher of the insurance device, to maintain a good state, must not save trouble, leaving the insurance device failure.Plastic crusher maintenance

粵公網安備 44190002002288號

免费专区-色哟哟 | 黄片在线免费观看 | 亚洲欧洲AV在线 | 亚洲AV无码久久蜜桃杨思敏 | 91少妇高潮呻吟无码精品 | 性做爰A片免费播放 | 水蜜桃视频在线免费观看 | 欧一美一性一交一大一片 | www.亚洲成人 | 懂色AV 粉嫩AV 蜜乳AV | 无码人妻精品一区二区三区欧美色涩 | 少妇老师洗澡被躁爽A片软件 | 无码国产伦一区二区三区视频 | 久久久无码国产精品无码三区三区 | 成年人免费在线观看视频网站 | 欧美婬乱片A片AAA毛片地址 | 在线免费观看黄色视频 | 在线观看免费黄色视频 | 蜜臀色欲AV无码人妻 | 亚洲AV无码秘 蜜桃渚光希 | 精品无码av一区二区鲁一鲁 | 国产精品二区一区二区AⅤ污介绍 | 91亚洲精品乱码久久久久久蜜桃 | 亚洲va欧美va国产va精品 | 国产人妻人伦精品午夜剧场 | 嫩模BBw搡BBBB搡BBBB | 国产精品96久久久久久 | 海角社区成人免费网站 | 无码人妻久久一区二区三区蜜桃 | 国产成人精品视频 | 亚洲A片无码毛片久久久站长工具 | 又硬又粗又黄又爽又大又紧视频 | 少妇高潮灌满白浆毛片免费看 | www.插插插.com | 国模精品无码一区二区免费蜜桃 | 国产一级婬片A片免费手机版宅男 | 成人亚洲A片Ⅴ一区二区三区动漫 | 91ThePorn国产 | 蜜桃av乱码人妻一二三区 | 久久久久久久久久久丰满 | 少妇人妻无套进入69va |